3xLogic VSX-PTZ-2MP-EXT20 Скачать руководство пользователя страница 75

Страница: 75 / 90

User Manual

| VISIX PTZ Network Camera

10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC

Besides configuring the recording schedule, you have to configure the settings on the

Motion Detection

and

Alarm Input Settings

interfaces. Please refer to Section

6.6.1

and

Section

6.6.4

for detailed information

Record Triggered by Motion | Alarm -‐

If you select

Motion | Alarm

, the video will be

recorded when the external alarm is triggered or the motion is detected.

Besides configuring the recording schedule, you have to configure the settings on the

Motion Detection

and

Alarm Input Settings

interfaces. Please refer to Section

6.6.1

and

Section

6.6.4

for detailed information

Figure 7-‐6

Edit Record Schedule

Check the checkbox

and click

to copy settings of this day to the

whole week. You can also check any of the checkboxes before the date and click

Click

to save the settings and exit the

Edit Record Schedule

interface.

Click

to save the settings.

7.3

Configuring Snapshot Settings

Purpose:

You can configure the scheduled snapshot and event-‐triggered snapshot. You can upload the captured
pictures to a FTP server.

Basic Settings

Steps:

Enter the Snapshot Settings interface:

Содержание VSX-PTZ-2MP-EXT20



























































































Результаты поиска

Содержание VSX-PTZ-2MP-EXT20

Отзывы:

3xLogic VSX-PTZ-2MP-EXT20, Руководство пользователя, Страница: 75 / 90

Результаты поиска

Содержание VSX-PTZ-2MP-EXT20

Отзывы: