3xLogic VSX-PTZ-2MP-EXT20 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 90

3xLogic VSX-PTZ-2MP-EXT20 Скачать руководство пользователя страница 60

User Manual

| VISIX 5 Inch Speed Dome Camera

CONFIGURING TEXT OVERLAY SETTINGS

Purpose:

You can customize the text overlay.

Steps:

1)

Enter the Text Overlay Settings interface:

Configuration

>

Advanced Configuration

>

Image

>

Text Overlay

2)

Check the checkbox in front of textbox to enable the on-‐screen display.

3)

Input the characters in the textbox.

4)

Use the mouse to click and drag the red text frame

in the live view window to adjust

the text overlay position.

5)

Click

.

NOTE:

There are up to 8 text overlays configurable.

Figure 6-‐40

Text Overlay Settings

6.6

Configuring and Handling Alarms

Purpose:

This section explains how to configure the network speed dome to respond to alarm events, including
motion   detection, external alarm input, video loss, tamper-‐proof and   exception. These events can
trigger   the alarm actions,   such as Notify Surveillance Center, Send Email,   Trigger Alarm Output,   etc.
For example, when an external alarm is triggered,   the network speed dome sends   a notification   to   an
e-‐mail address.

CONFIGURING MOTION DETECTION

Purpose:

Motion detection is a feature which can trigger alarm actions and actions of recording videos when
the motion occurred in the surveillance scene.

Task:

«
...
58
59
60
61
62
...
»

Содержание VSX-PTZ-2MP-EXT20



























































































Отзывы:

Нет отзывов