![background image](http://html2.mh-extra.com/html/zoll/propaq-md/propaq-md_service-manual_3990958043.webp)
Maintenance Tests
9650-0807-01 Rev. C
ZOLL Propaq MD Service Manual
37
20.0 NIBP Calibration Check
Equipment
NIBP Simulator, dual lumen hose w/ NIBP test fixture cuff (9100-3072-TF) or equivalent
Note:
If ECG simulator is connected to the device, either disconnect ECG simulator or
disable the Smart Cuff feature in the Supervisor Menu.
Setup
Attached the hose connected to the T-fitting of the NIBP test fixture cuff to the pressure port of
the NIBP simulator. Set simulator to Static Pressure.
Do This...
Observe This...
Pass/Fail
20.1 Turn on the Propaq unit.
Note
: If the unit is in AED mode, press
the
Manual
quick access key to go into
manual mode.
20.2 Connect a dual lumen hose from the NIBP
simulator to the NIBP port of the Propaq.
20.3 On the Propaq unit, do the following to
enter the NIBP Test control panel:
•
Press the More
(
) then the Setup
(
) quick access keys.
•
Use the navigation keys to select
Supervisor
>
Service
>
Device
Tests
>
NIBP Test
.
Note
: You need a supervisor passcode to
enter the Supervisor menu.
20.4 From the Propaq NIBP Test control panel,
use the navigation keys to select:
•
Close Valve
•
Turn Pump On
20.5 Monitor the pressure reported by the
external pressure standard.
20.6 Once the pressure reaches the target
pressure of 50 +/- 5 mmHg, use the
navigation keys to select
Turn Pump Off
.
20.7 Allow the system to stabilize for at least
10 seconds.
20.8 Verify that the primary transducer agrees
with the reading on the NIBP simulator.
Reading should be within
3mmHg.
o
o
20.9 Verify that the safety transducer agrees
with the reading on the NIBP simulator.
Reading should be within
4mmHg.
o
o
Summary of Contents for Propaq MD
