ZCS AZZURRO 1PH HYD3000-ZP1 User Manual Download Page 166

Page: 166 / 195

User’s Manual 1PH HYD3000-HYD6000-ZP1

Rev. 1.0 01/09/2023

Identification: MD-AL-GI-00

Rev. 1.1 of 27/01/2023 - Application: GID

165/193

network for 4G transmission; if this network is not present or the signal is weak, the SIM will

use a different network or will limit the data transmission speed). Ensure that the installation

location is suitable for 4G signal transmission and that there are no obstacles that could affect

data transmission.

Check the status of the 4G adapter and that there are no external signs of wear or damage.

Summary of Contents for AZZURRO 1PH HYD3000-ZP1




































































































































































































Search results

Summary of Contents for AZZURRO 1PH HYD3000-ZP1

Reviews:

Related manuals for AZZURRO 1PH HYD3000-ZP1

Brands by name

Popular brands

ZCS AZZURRO 1PH HYD3000-ZP1, User Manual

Search results

Summary of Contents for AZZURRO 1PH HYD3000-ZP1

Reviews:

Related manuals for AZZURRO 1PH HYD3000-ZP1

Brands by name

Popular brands