background image

Hydraulic Digger 

2-35 

fire.It must do as follow: 

 

● 

Check the level of the electrolyte timely,and supply the distilled 

water to make the level of the electrolyte between the “top level” 

and the “low level” line.If the electrolyte of the accumulator lower 

than eh “low level”line,it doesn’t have to use the accumulator 

● 

Operating the accumulator,it need wear the safety glass and the 

rubber glove 

● 

It doesn’t allow have the fire near the accumulator 

● 

If the eye

the cloth

the skin have the vitriol,it must use the lots 

of water to wash and go to the hospital 

● 

Before operating the accumulator,it should turn the key to”OFF” 

● 

Use the electric torch to check the electrolyte of the 

accumulator,it should stop the antichattering system. 

● 

The end of the sealed accumulator dilates,it show the 

accumulator freezed.When the accumulator freezed,it doesn’t 

electricize or connect and start the engine.The temperature 

doesn’t more than 15

0

C when heat up the freezed 

accumulator.Otherwise,it explodes 

Explosion-proof of the accumulator 

 Warning: the electric spark or the flame can make the 

hydrogen

 

of the accumulator explodes. Avoid 

Summary of Contents for YC25-8














































































































































































































Reviews: