background image

Hydraulic Digger 

4-47 

 

Reason for the Technical Trouble& Resolve 

Trouble Reason 

Resolve 

Problem for start the engine 

Replace or check the engine 

Lack electrification of the battery 

Electrification or replace the battery 

Error use for the line or the piston of 

the warm-up 

Mend or replace the warm-up piston 

Error of the oil injection positive 

Check the oil injection positive 

The pipe laying obstructed 

Clean the pipe laying 

The filter of the fuel obstructed 

Clean or replace the filter of the fuel 

The fuel system has the water

the 

dust or the air. 

Ejectment the air, clean the pipe 

laying 

The nozzle dirty or the pressure of oil 

injection lower 

Maintain the nozzle 

The trouble of the fuel injection pump 

Contact assistant service 

The fuel lacks 

Immit the oil 

 

 

 

 

1.The engine 

couldn’t start 

or start difficult 

The intake/vent system obstructed 

Ejectment the trouble 

It have many air 

Contact assistant service 

The filter of the fuel obstructed 

Clean the filter 

The fuel system has the    dust or the 

air. 

Vent and clean the oil line 

The filter obstructed,the nozzle dirty 

or trouble 

Check them 

The high-pressure oil pipe destroyed 

Replace the high-pressure oil pipe 

The fuel lacks 

Immit the oil 

The velometer couldn’t adjust 

Contact assistant service 

The trouble of the fuel injection pump 

Contact assistant service 

 

 

 

2.The engine 

knocking

running 

irregularly or 

stop  

Error of spurt oil positive or the nozzle 

clip 

Check them 

 

Trouble Reason 

Resolve 

Summary of Contents for YC25-8














































































































































































































Reviews:

Related manuals for YC25-8