Yuchai YC25-8 User Manual Download

Page: 149 / 205

Hydraulic Digger

5-19

3. Clean the oil tank

Clean it every 250hours

1) Vent the fuel to the container

2) Take-down the oil drain plug, take out the fliter. Top up half of the

oil tank, and vent it again.

3) Clean the filter and replace.

4) Install the oil drain plug again. Through the fliter top up the fuel

5) Vent the air of the pipe laying

Caution: Don’t use the trichlene to washing the inside of the

oil tank, it only use the diesel oil

4. Exhaust of the fuel loop

It need to exhaust the air before start the engine when it replaces

filter core of the fuel

、

cut off the pipe of the fuel

、

clean the filter of

the fuel and make the air into the fuel loop.

Exhaust of YC25-2 type fuel loop

1) Open the vent nut of the base of the fuel filter

2) Run and press the pump piston till no air pour from the fuel

3) Close the vent nut.

Summary of Contents for YC25-8














































































































































































































Search results

Summary of Contents for YC25-8

Reviews:

Related manuals for YC25-8

Brands by name

Popular brands

Yuchai YC25-8, User Manual

Search results

Summary of Contents for YC25-8

Reviews:

Related manuals for YC25-8

Brands by name

Popular brands