Yealink MeetingSpace VC200 Page 96 Administrator'S Manual Download

Page: 96 / 232

| Configuring Account Settings |

Parameter

Description

Configuration Method

Transport

Configure the transport protocol

for transmitting the SIP

signaling.
The supported protocols are as

follows:
•

UDP—

it provides the

best transmission for SIP

signaling.

•

TCP

—it provides a reliable

transmission for SIP

signaling.

•

TLS

—it provides a safe

transmission for SIP

signaling. TLS is available

only when the device is

registered on a SIP server

that supports TLS.

•

DNS-NAPTR

—the device

performs the DNS NAPTR

and SRV request to find the

service type and the port if

no server port is given.

Default

: TCP.

Web user interface

Server Expires

The registration timeout (in

seconds) of the device.
After the timeout, the device will

send the registration request to

the server again.

Default

: 3600 seconds.

Web user interface

Keep Alive Interval

Configure the interval (in

seconds) that the device sends

keep-alive messages to the SIP

server, so that the SIP server can

remain connected to the device.

Default

: 30 seconds.

Web user interface

Logging out of the Video Conference Platform

Procedure

Do one of the following:
• On your web user interface, go to

Account

VC Platform

Log Out

• On your VCS, go to

More

Setting

Advanced

Video Conference Platform

Log out

On your VP59, tap

Setting

Advanced

Video Conference Platform

Log out

• On your CTP20, go to

Setting

Advanced

Video Conference Platform

Log out

It prompts whether to log out the current account.

Summary of Contents for MeetingSpace VC200









































































































































































































































Search results

Summary of Contents for MeetingSpace VC200

Reviews:

Related manuals for MeetingSpace VC200

Brands by name

Popular brands

Yealink MeetingSpace VC200, Administrator'S Manual

Search results

Summary of Contents for MeetingSpace VC200

Reviews:

Related manuals for MeetingSpace VC200

Brands by name

Popular brands