Yealink MeetingSpace VC200 Page 232 Administrator'S Manual Download

Page: 232 / 232

| Troubleshooting |

232

• On your CTP20, tap

Setting

Select the desired list to view the status.
For CTP20, you can view the corresponding status in the module of

Collaboration Touch Panel

Host Status

Viewing Call Statistics

About this task

If voice quality is poor during a call, you can view call statistics to find out the reason. The call statistics includes:
•

Bandwidth

: the received and the sent bandwidth.

•

Video

: the definition, the codec, the bandwidth, the frame rate, the jitter, the packet and its loss rate.

• The protocol used to placing calls.
• The device information.
•

Audio

: the codec, the bandwidth, the sample rate, the frame rate, the jitter, the packet and its loss rate.

•

Content

: the codec, the bandwidth, the definition and the frame rate.

Procedure

Do one of the following during a call:
• For your VC880/VC800/VC500/VC200/PVT980/PVT950, on your web user interface, click

Home

Position your mouse pointer over the desired far site, and click

• On your VCS:

For VC880/VC800/VC500/VC200/PVT980/PVT950, on your remote control, press

or OK key to open

Talk Menu

, and then select

Call Statistics

On your VP59, tap

Call Statistics

• On your CP960 conference phone, go to

More

Statistics

Tap the desired far site to view the call statistics.

•

On your CTP20, tap

Call Statistics

If you are having a conference, tap Participant, and tap

Call Statistics

beside the desired participant.

Summary of Contents for MeetingSpace VC200









































































































































































































































Search results

Summary of Contents for MeetingSpace VC200

Reviews:

Related manuals for MeetingSpace VC200

Brands by name

Popular brands

Yealink MeetingSpace VC200, Administrator'S Manual

Search results

Summary of Contents for MeetingSpace VC200

Reviews:

Related manuals for MeetingSpace VC200

Brands by name

Popular brands