Yealink MeetingSpace VC200 Page 72 Administrator'S Manual Download

Page: 72 / 232

| Configuring Network Settings |

Parameter

Description

Configuration Method

Data Priority

Configure the DSCP

(Differentiated Services Code

Point) for data packets.

Note

: the default value is 63.

The greater the number is, the

higher the priority is. If you

change this parameter, the

system will reboot to make the

change take effect.

Web user interface
Endpoint
CTP20

Configuring MTU

Data packets that exceed the maximum transmission unit (MTU) size for any router or segment along the network

path may be fragmented or dropped, which may result in poor quality video at the receiving device. You can set the

maximum MTU size of the data packets sent by the system.

About this task

Configure the MTU size used in calls based on the network bandwidth settings. If the video becomes blocky or

network errors occur, packets may be too large; decrease the MTU. If the network is burdened with unnecessary

overhead; packets may be too small, increase the MTU.

Procedure

Do one of the following:
• On your web user interface, go to

Network

Advanced

MTU

• On your VCS:

For VC880/VC800/VC500/PVT980/PVT950,
On your VC200, go to

More

Network

Wired Network

Advanced Network

Network MTU

(1000-1500)

On your VP59, tap

Setting

Advanced

Advanced Network

Network MTU (1000-1500)

• On your CTP20, tap

Setting

Advanced

Advanced Network

Network MTU (1000-1500)

Configure and save the following settings:

Parameter

Description

Configuration Method

Network MTU (1000-1500)

Specify the maximum MTU size

(bytes) of data packets sent by

the system.

Note

: the value can be any

integer from 1000 to 1500. The

default value is 1500.
If you change this parameter, the

system will reboot to make the

change take effect.

Web user interface
Endpoint
CTP20

Summary of Contents for MeetingSpace VC200









































































































































































































































Search results

Summary of Contents for MeetingSpace VC200

Reviews:

Related manuals for MeetingSpace VC200

Brands by name

Popular brands

Yealink MeetingSpace VC200, Administrator'S Manual

Search results

Summary of Contents for MeetingSpace VC200

Reviews:

Related manuals for MeetingSpace VC200

Brands by name

Popular brands