Yealink MeetingSpace VC200 Administrator'S Manual Download Page 75

Page: 75 / 232

| Configuring Account Settings |

Parameter

Description

Configuration Method

Port

Configure the port of the

outbound proxy server.

Note:

the default port number

is 5060. The value can be any

integer from 0 to 65535.

Web user interface
Endpoint
CTP20

Transport

Specify the transport protocol

for transmitting the SIP

signaling.
The supported protocols are as

follows:
•

UDP

—it provides the

best transmission for SIP

signaling.

•

TCP

—it provides a reliable

transmission for SIP

signaling.

•

TLS

—it provides a safe

transmission for SIP

signaling. TLS is available

only when the device is

registered on a SIP server

that supports TLS.

• DNS-NAPTR—the device

performs the DNS NAPTR

and SRV request to find the

service type and the port if

no server port is given.

Default

: UDP.

Web user interface
Endpoint
CTP20

Server Expires

The registration timeout (in

seconds) of the device.
After the timeout, the device will

send the registration request to

the SIP server again.

Default

: 3600 seconds.

Web user interface
Endpoint
CTP20

Keep Alive Interval

Configure the interval (in

seconds) that the device sends

keep-alive messages to the SIP

server, so that the SIP server can

remain connected to the device.

Default

: 30.

Web user interface

Summary of Contents for MeetingSpace VC200









































































































































































































































Search results

Summary of Contents for MeetingSpace VC200

Reviews:

Yealink MeetingSpace VC200, Administrator'S Manual, Page: 75 / 232

Search results

Summary of Contents for MeetingSpace VC200

Reviews: