manualshive.com logo in svg

Yamaha XV19SX(C), Service Manual, Page: 374 / 494

Share
Download
Yamaha XV19SX(C) Service Manual Download Page 374

FUEL TANK

6-5

CAUTION:

EC1D71022

• Be sure to disconnect the fuel outlet hose 

by hand. Do not forcefully disconnect the 
hose with tools.

• Although the fuel has been removed from 

the fuel tank be careful when removing the 
fuel hoses, since there may be fuel remain-
ing in them.

NOTE:

• Remove the fuel hose manually without using 

any tools.

• Before removing the hoses, place a few rags in 

the area under where they will be removed.

3. Remove:

• Fuel pump

CAUTION:

ECA14720

• Do not drop the fuel pump or give it a 

strong shock.

• Do not touch the base section of the fuel 

sender.

EAS26670

CHECKING THE FUEL PUMP BODY

1. Check:

• Fuel pump body

Obstruction 

→

 Clean.

Cracks/damage 

→

 Replace fuel pump as-

sembly.

2. Check:

• Diaphragms and gaskets

Tears/fatigue/cracks 

→

 Replace fuel pump 

assembly.

EAS26690

CHECKING THE FUEL PUMP OPERATION

1. Check:

• Fuel pump operation

Refer to “CHECKING THE FUEL PUMP” on 
page 7-90.

EAS26710

INSTALLING THE FUEL PUMP

1. Install:

• Fuel pump

NOTE:

• Do not damage the installation surfaces of the 

sub-fuel tank when installing the fuel pump.

• Always use a new fuel pump gasket.

• Install the fuel pump as shown in the illustra-

tion.

• Align the projection “a” on the fuel pump with 

the slot in the fuel pump bracket.

• Tighten the fuel pump bolts in the proper tight-

ening sequence as shown.

2. Connect:

• Fuel outlet hose

3. Install:

• Fuel hose connector cover “1”

CAUTION:

EC1D71023

When installing the fuel outlet hose, make 
sure that it is securely connected, and that 
the fuel hose connector cover is installed 
correctly, otherwise the fuel outlet hose will 
not be properly installed.

NOTE:

• Install the fuel outlet hose connector securely 

onto the sub fuel tank until a distinct “click” is 
heard, and then make sure that it does not 
come loose.

• Install the holder “a” of the fuel hose connector 

cover, and then install the holder “b”. After in-
stalling the fuel hose connector cover, make 
sure that it is installed securely.

ET1D71025

INSTALLING THE FUEL TANK

1. Install:

• Fuel tank

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Install the fuel tank.

T

 

R

.

.

 

Fuel pump bolt

5 Nm (0.5 m·kg, 3.6 ft·lb)

a

1

b

Summary of Contents for XV19SX(C)















































































































































































































































































































































































































































































































Reviews:

No comments