Yamaha VIRAGO XV250P Owner'S Manual Download Page 39

Page: 39 / 98

OPERATION AND IMPORTANT RIDING POINTS

5-6

EAU00452*

0–1,000 km (0–600 mi)
Avoid prolonged operation above 1/3
throttle.

1,000–1,600 km (600–1,000 mi)
Avoid prolonged operation above 1/2
throttle.

1,600 km and beyond
The vehicle can now be operated nor-
mally.

EC000059*

CAUTION:

●

After 1,000 km (600 mi) of oper-
ation, the engine oil must be
changed, the oil filter element
replaced, and the oil strainer
cleaned.

●

If any engine trouble should oc-
cur during the engine break-in
period, immediately have a
Yamaha dealer check the vehi-
cle.

EAU00460

Parking

When parking, stop the engine, and
then remove the key from the main
switch.

EW000058

WARNING

●

Since the engine and exhaust
system can become very hot,
park in a place where pedestri-
ans or children are not likely to
touch them.

●

Do not park on a slope or on
soft ground, otherwise the
motorcycle may overturn.

E_2uj.book Page 6 Friday, March 30, 2001 2:06 PM

Summary of Contents for VIRAGO XV250P



































































































Search results

Summary of Contents for VIRAGO XV250P

Reviews:

Related manuals for VIRAGO XV250P

Brands by name

Popular brands

Yamaha VIRAGO XV250P, Owner'S Manual

Search results

Summary of Contents for VIRAGO XV250P

Reviews:

Related manuals for VIRAGO XV250P

Brands by name

Popular brands