manualshive.com logo in svg

Yamaha VIRAGO XV250P, Owner'S Manual

Share
Download
Yamaha VIRAGO XV250P Owner'S Manual Download Page 67

PERIODIC MAINTENANCE AND MINOR REPAIR

6-28

6

EAU02939

Checking the front fork 

The condition and operation of the front
fork must be checked as follows at the
intervals specified in the periodic main-
tenance and lubrication chart.

To check the condition

EW000115

WARNING

@ 

Securely support the motorcycle so
that there is no danger of it falling
over. 

@

Check the inner tubes for scratches,
damage and excessive oil leakage.

To check the operation

1. Place the motorcycle on a level

surface and hold it in an upright
position.

2. While applying the front brake,

push down hard on the handle-
bars several times to check if the
front fork compresses and re-
bounds smoothly.

EC000098

CAUTION:

@ 

If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or re-
pair it. 

@

EAU00794

Checking the steering 

Worn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as fol-
lows at the intervals specified in the pe-
riodic maintenance and lubrication
chart.

1. Place a stand under the engine to

raise the front wheel off the
ground.

EW000115

WARNING

@ 

Securely support the motorcycle so
that there is no danger of it falling
over. 

@

E_2uj.book  Page 28  Friday, March 30, 2001  2:06 PM

Summary of Contents for VIRAGO XV250P



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands