manualshive.com logo in svg

Yamaha VIRAGO XV250P, Owner'S Manual

Share
Download
Yamaha VIRAGO XV250P Owner'S Manual Download Page 76

PERIODIC MAINTENANCE AND MINOR REPAIR

6-37

6

6. Loosen the locknut and the drive

chain slack adjusting nut on both
ends of the swingarm.

7. Remove the axle nut.
8. Pull the wheel axle out, and then

remove the wheel.

EAU01696

To install the rear wheel 

1. Insert the wheel axle from the

right-hand side, and then install
the drive chain onto the rear
sprocket.

2. Install the axle nut, and then lower

the rear wheel so that it is on the
ground.

3. Install the brake rod onto the brake

camshaft lever, and then install
the brake pedal free play adjusting
nut onto the brake rod.

4. Install the brake torque rod bolt at

the swingarm, tighten it to the
specified torque, and then install
the cotter pin.

EW000110

WARNING

@ 

Always use a new cotter pin for the
axle nut. 

@

5. Adjust the drive chain slack. (See

page 6-22 for drive chain slack ad-
justment procedures.)

6. Tighten the axle nut to the speci-

fied torque.

7. Adjust the brake pedal position

and free play. (See page 6-18 for
brake pedal position and free play
adjustment procedures.)

EW000103

WARNING

@ 

After adjusting the brake pedal free
play, check the operation of the
brake light. 

@ 

1. Axle nut
2. Axle nut cotter pin
3. Locknut
4. Drive chain slack adjusting nut
5. Alignment marks

Tightening torque:

Brake torque rod bolt:

23 Nm (2.3 m·kgf, 17 ft·lb)

Tightening torque:

Axle nut:

104 Nm (10.4 m·kgf, 75 ft·lb)

E_2uj.book  Page 37  Friday, March 30, 2001  2:06 PM

Summary of Contents for VIRAGO XV250P



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands