manualshive.com logo in svg

Yamaha VIRAGO XV250P, Owner'S Manual

Share
Download
Yamaha VIRAGO XV250P Owner'S Manual Download Page 88

9-1

9

EAU01039

9-

CONSUMER INFORMATION

EAU02944

Identification numbers 

Record the key identification number,
vehicle identification number and mod-
el label information in the spaces pro-
vided below for assistance when
ordering spare parts from a Yamaha
dealer or for reference in case the vehi-
cle is stolen.

1. KEY IDENTIFICATION NUMBER:

CA-02E

2. VEHICLE IDENTIFICATION 

NUMBER:

CA-02E

3. MODEL LABEL INFORMATION:

CA-01E

EAU01042

Key identification number 

The key identification number is
stamped into the key. Record this num-
ber in the space provided and use it for
reference when ordering a new key.

EAU01043

Vehicle identification number 

The vehicle identification number is
stamped into the steering head pipe.
Record this number in the space pro-
vided.

NOTE:

@ 

The vehicle identification number is
used to identify your motorcycle and
may be used to register your motor-
cycle with the licensing authority in
your area. 

@

1. Key identification number

1. Vehicle identification number

E_2uj.book  Page 1  Friday, March 30, 2001  2:06 PM

Summary of Contents for VIRAGO XV250P



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands