manualshive.com logo in svg

Yamaha VIRAGO XV250P, Owner'S Manual

Share
Download
Yamaha VIRAGO XV250P Owner'S Manual Download Page 78

PERIODIC MAINTENANCE AND MINOR REPAIR

6-39

6

EAU01562

Troubleshooting chart 

EW000125

WARNING

@ 

Keep away open flames and do not smoke while checking or working on the fuel system. 

@

Check the fuel level in
the fuel tank.

1. Fuel

There is enough fuel.

There is no fuel.

Check the compression.

Supply fuel.

Operate the electric starter.

2. Compression

There is compression.

There is no compression.

Check the ignition.

Have a Yamaha dealer
check the vehicle.

Remove the spark plugs
and check the electrodes.

3. Ignition

Wet

Dry

Wipe off with a dry cloth and correct the 
spark plug gaps, or replace the spark plugs.

Have a Yamaha dealer check the vehicle.

The engine does not start.
Check the battery.

Open the throttle halfway and 
operate the electric starter.

Operate the electric starter.

4. Battery

The engine turns over 
quickly.

The engine turns over 
slowly.

The battery is good.

Check the electrolyte and battery
lead connections, and charge the
battery if necessary.

The engine does not start. 
Have a Yamaha dealer 
check the vehicle.

The engine does not start. 
Check the compressoin.

E_2uj.book  Page 39  Friday, March 30, 2001  2:06 PM

Summary of Contents for VIRAGO XV250P



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands