manualshive.com logo in svg

Yamaha VIRAGO XV250P, Owner'S Manual

Share
Download
Yamaha VIRAGO XV250P Owner'S Manual Download Page 54

PERIODIC MAINTENANCE AND MINOR REPAIR

6-15

6

EW000083

WARNING

@ 

Proper loading of your motorcycle
is important for several characteris-
tics of your motorcycle, such as
handling, braking, performance and
safety. Do not carry loosely packed
items that can shift. Securely pack
your heaviest items close to the
center of the motorcycle, and dis-
tribute the weight evenly from side
to side. Properly adjust the suspen-
sion for your load, and check the
condition and pressure of your tires.
NEVER OVERLOAD YOUR MOTOR-
CYCLE. Make sure the total weight
of the cargo, rider, passenger, and
accessories (cowling, saddlebags,
etc. if approved for this model) does
not exceed the maximum load of the
motorcycle. Operation of an over-
loaded motorcycle could cause tire
damage, an accident, or even injury. 

@

Tire inspection
Always check the tires before operating
the motorcycle. If a tire tread shows
crosswise lines (minimum tread depth),
if the tire has a nail or glass fragments
in it, or if the sidewall is cracked, con-
tact a Yamaha dealer immediately and
have the tire replaced.

CE-10E

CE-23E

EAU00680

WARNING

@ 

●

It is dangerous to ride with a
worn-out tire. When a tire tread
begins to show crosswise lines,
have a Yamaha dealer replace
the tire immediately.

●

The replacement of all wheel-
and brake-related parts, includ-
ing the tires, should be left to a
Yamaha dealer, who has the
necessary professional knowl-
edge and experience.

●

It is not recommended to patch
a punctured tube. If unavoid-
able, however, patch the tube
very carefully and replace it as
soon as possible with a high-
quality product. 

@

FRONT

Manufacturer

Size

Model

CHENG SHIN

3.00-18 47P

C-916

REAR

Manufacturer

Size

Model

CHENG SHIN

130/90-15M/C 66P

C-915

Minimum tire tread depth 
(front and rear)

1.0 mm (0.04 in)

E_2uj.book  Page 15  Friday, March 30, 2001  2:06 PM

Summary of Contents for VIRAGO XV250P



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands