Yamaha VIRAGO XV250P Owner'S Manual Download Page 66

Page: 66 / 98

PERIODIC MAINTENANCE AND MINOR REPAIR

6-27

EAU03164

Checking and lubricating the
brake and clutch levers

The operation of the brake and clutch
levers should be checked before each
ride, and the lever pivots should be lu-
bricated if necessary.

EAU03165

Checking and lubricating the
sidestand

The operation of the sidestand should
be checked before each ride, and the
sidestand pivot and metal-to-metal
contact surfaces should be lubricated if
necessary.

EW000113

WARNING

If the sidestand does not move up
and down smoothly, have a Yamaha
dealer check or repair it.

Recommended lubricant:

Lithium-soap-based grease
(all-purpose grease)

Recommended lubricant:

Lithium-soap-based grease
(all-purpose grease)

E_2uj.book Page 27 Friday, March 30, 2001 2:06 PM

Summary of Contents for VIRAGO XV250P



































































































Search results

Summary of Contents for VIRAGO XV250P

Reviews:

Brands by name

Popular brands

Yamaha VIRAGO XV250P, Owner'S Manual

Search results

Summary of Contents for VIRAGO XV250P

Reviews:

Brands by name

Popular brands