Yamaha VIRAGO XV250P Owner'S Manual Download Page 64 | Manualshive

Page: 64 / 98

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-25

6

EAU03006

Lubricating the drive chain

The drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrica-
tion chart, otherwise it will quickly wear
out, especially when riding in dusty or
wet areas. Service the drive chain as
follows.

EC000097

CAUTION:

@

The drive chain must be lubricated
after washing the motorcycle or
riding in the rain.

@

1. Clean the drive chain with kero-

sene and a small soft brush.

ECA00053

CAUTION:

@

To prevent damaging the O-rings,
do not clean the drive chain with
steam cleaners, high-pressure
washers or inappropriate solvents.

@

2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive

chain with a special O-ring chain
lubricant.

ECA00052

CAUTION:

@

Do not use engine oil or any other
lubricants for the drive chain, as
they may contain substances that
could damage the O-rings.

@

EAU03297

Checking and lubricating the
cables

The operation of all control cables and
the condition of the cables should be
checked before each ride, and the ca-
bles and cable ends should be lubricat-
ed if necessary. If a cable is damaged
or does not move smoothly, have a
Yamaha dealer check or replace it.

EW000111

WARNING

@

Damage to the outer housing of ca-
bles may result in internal rusting
and cause interference with cable
movement. Replace damaged ca-
bles as soon as possible to prevent
unsafe conditions.

@

Recommended lubricant:

Yamaha Chain and Cable Lube
or engine oil SAE 10W-30
(API SE)

E_2uj.book Page 25 Friday, March 30, 2001 2:06 PM

«
...
62
63
64
65
66
...
»

Summary of Contents for VIRAGO XV250P



































































































Reviews:

No comments

Related manuals for VIRAGO XV250P

Brand: R&G Pages: 10

Nils Extreme MTW03

Brand: Abisal Pages: 21

EC-SIX DAYS - PART LIST 2011

Brand: GAS GAS Pages: 6

MULTISTRADA 1200S

Brand: Ducati Pages: 311

Brand: Honda Pages: 140

Brand: Yamaha Pages: 86

Brand: Yamaha Pages: 86

Brand: Yamaha Pages: 86

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 119

MIO AL115S 2010

Brand: Yamaha Pages: 80

Brand: Yamaha Pages: 112

Brand: Yamaha Pages: 146

Brand: Yamaha Pages: 78

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 146

TMAX XP530E-A 2017

Brand: Yamaha Pages: 676

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands