Yamaha VIRAGO XV250P Owner'S Manual Download Page 20 | Manualshive

Page: 20 / 98

background image

3-1

3

EAU00027

3-

INSTRUMENT AND CONTROL FUNCTIONS

EAU00028

Main switch

The main switch controls the ignition
and lighting systems. The various main
switch positions are described below.

EAU00032

ON
All electrical systems are supplied with
power, the headlight, meter lighting,
taillight and front position lights come
on, and the engine can be started. The
key cannot be removed.

EAU00038

OFF
All electrical systems are off. The key
can be removed.

EAU00050

P (Parking)
The taillight and position lights are on,
but all other electrical systems are off.
The key can be removed.
The key must be pushed in from the
“OFF” position to be turned to “P”.

ECA00043

CAUTION:

@

Do not use the parking position for
an extended length of time, other-
wise the battery may discharge.

@

EAU00056

Indicator lights

EAU00064

High beam indicator light
“HIGH BEAM”
This indicator light comes on when the
high beam of the headlight is switched
on.

EAU00062

Neutral indicator light “NEUTRAL”
This indicator light comes on when the
transmission is in the neutral position.

EAU00059

Turn signal indicator light “TURN”
This indicator light flashes when the
turn signal switch is pushed to the left
or right.

1. High beam indicator light “HIGH BEAM”
2. Neutral indicator light “NEUTRAL”
3. Turn signal indicator light “TURN”

E_2uj.book Page 1 Friday, March 30, 2001 2:06 PM

«
...
18
19
20
21
22
...
»

Summary of Contents for VIRAGO XV250P



































































































Reviews:

No comments

Related manuals for VIRAGO XV250P

Brand: N-Com Pages: 2

Brand: N-Com Pages: 64

Brand: BMW Pages: 288

Easyrack 6622520 01 01

Brand: hepco & becker Pages: 4

Brand: KTM Power Parts Pages: 22

Brand: Crivit Pages: 30

Brand: Isotta Pages: 2

Brand: Yamaha Pages: 287

Brand: Yamaha Pages: 109

Brand: Shark Pages: 76

Brand: Yamaha Pages: 80

Brand: Yamaha Pages: 278

Brand: VESPA Pages: 25

Brand: VESPA Pages: 308

Brand: Dräger Pages: 164

Brand: Abus Pages: 41

: 6519512 00 22-01-40

Brand: hepco & becker Pages: 9

Brand: Honda Pages: 293

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands