manualshive.com logo in svg

Yamaha VIRAGO XV250P, Owner'S Manual

Share
Download
Yamaha VIRAGO XV250P Owner'S Manual Download Page 34

5-1

5

EAU00372

5-

OPERATION AND IMPORTANT RIDING POINTS

EAU00373

WARNING

@ 

●

Become thoroughly familiar
with all operating controls and
their functions before riding.
Consult a Yamaha dealer re-
garding any control or function
that you do not thoroughly
understand.

●

Never start the engine or operate
it in a closed area for any length
of time. Exhaust fumes are poi-
sonous, and inhaling them can
cause loss of consciousness
and death within a short time. Al-
ways make sure that there is ad-
equate ventilation.

●

Before starting out, make sure
that the sidestand is up. If the
sidestand is not raised com-
pletely, it could contact the
ground and distract the opera-
tor, resulting in a possible loss
of control. 

@

EAU00376

CAUTION:

@ 

●

Make sure not to store personal
items near the air cleaner in-
take, otherwise air intake will be
blocked and performance will
suffer.

●

Make sure not to put anything
near the battery and its termi-
nals, otherwise electrical failure
and acid corrosion may result. 

@

E_2uj.book  Page 1  Friday, March 30, 2001  2:06 PM

Summary of Contents for VIRAGO XV250P



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands