Yamaha VIRAGO XV250P Owner'S Manual Download Page 63

Page: 63 / 98

PERIODIC MAINTENANCE AND MINOR REPAIR

6-24

NOTE:

Using the alignment marks on each
side of the swingarm, make sure that
both chain pullers are in the same posi-
tion for proper wheel alignment.

EC000096

CAUTION:

Improper drive chain slack will over-
load the engine as well as other vital
parts of the motorcycle and can lead
to chain slippage or breakage. To
prevent this from occurring, keep
the drive chain slack within the
specified limits.

5. Tighten the locknuts, and then

tighten the axle nut to the specified
torque.

6. Insert a new cotter pin into the axle

nut, and then bend its ends as
shown.

NOTE:

Make sure that two notches in the axle
nut are aligned with the hole through
the wheel axle, otherwise further tight-
en the axle nut until they are.

EW000110

WARNING

Always use a new cotter pin for the
axle nut.

7. Adjust the brake pedal free play.

(See page 6-18 for brake pedal
free play adjustment procedures.)

EW000103

WARNING

After adjusting the brake pedal free
play, check the operation of the
brake light.

Tightening torque:

Axle nut:

104 Nm (10.4 m·kgf, 75 ft·lb)

1. Cotter pin

E_2uj.book Page 24 Friday, March 30, 2001 2:06 PM

Summary of Contents for VIRAGO XV250P



































































































Search results

Summary of Contents for VIRAGO XV250P

Reviews:

Brands by name

Popular brands

Yamaha VIRAGO XV250P, Owner'S Manual

Search results

Summary of Contents for VIRAGO XV250P

Reviews:

Brands by name

Popular brands