manualshive.com logo in svg

Yamaha VIRAGO XV250P, Owner'S Manual

Share
Download
Yamaha VIRAGO XV250P Owner'S Manual Download Page 75

PERIODIC MAINTENANCE AND MINOR REPAIR

6-36

6

8. Connect the speedometer cable.

EAU01550*

Rear wheel 

To remove the rear wheel 

EW000122

WARNING

_ 

●

It is advisable to have a Yamaha
dealer service the wheel.

●

Securely support the motor-
cycle so that there is no danger
of it falling over. 

_

1. Remove the axle nut cotter pin

and the brake torque rod cotter
pin.

2. Loosen the axle nut and the brake

torque rod nut at the brake shoe
plate.

3. Lift the rear wheel off the ground

according to the procedure on
page 6-34.

4. Disconnect the brake torque rod

from the brake shoe plate by re-
moving the nut and the bolt.

5. Remove the brake pedal free play

adjusting nut, and then disconnect
the brake rod at the brake cam-
shaft lever.

Tightening torque:

Front wheel axle pinch bolt:

20 Nm (2.0 m·kgf, 14 ft·lb)

1. Brake torque rod
2. Brake torque rod cotter pin
3. Brake torque rod bolt
4. Brake rod
5. Brake pedal free play adjusting nut
6. Brake cam shaft lever

E_2uj.book  Page 36  Friday, March 30, 2001  2:06 PM

Summary of Contents for VIRAGO XV250P



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands