VOICE EDIT MODE
This indicates the EG segment ("seg1-3" or
"rel1") from which the pitch EG graphic display
begins. If the EG is too long to be fully shown in
the LCD, hold SHIFT and press F7 or F8 to change
the segment from which the display begins.
This indicates the time length shown by the
graphic display. To change this, hold SHIFT and
press F1-F6 (x1, x2, x5, x10, x20, x50). The
exact length of time will depend on the range.
When the pitch EG range is 1 octave, the
graphic display will cover approximately 0.5 sec-
onds at "x1" and approximately 5 seconds at
"x50".
The pitch EG is graphically displayed.
R1-R3, RR1 (0...63): Keyon Rates 1-3 and the
Release Rate determine the speed of the pitch
EG. Higher settings result in faster change. A
rate of 63 will jump immediately to the following
level.
L0-L3, RL (-64...+63): Keyon Levels 0-3 and
the Release Level determine the levels of the
pitch EG. Positive settings raise the pitch and
negative settings lower the pitch.
Rates and Levels; When you press a key, the
pitch will begin at the level of L0, and will
change at the rate of R1 to level L1. When the
level reaches L1, the pitch will change at the
rate of R2 to the level of L2. When the pitch
reaches L2, it will change at the rate of R3 to the
level of L3 and will stay at L3 as long as the key
is pressed.
When the key is released, the pitch will
change at the rate of RR to the level of RL.
Note: Even if the AWM pitch EG and the AFM pitch
EG have identical Rate settings, there will be
slight differences in the timing of the pitch
change.
AWM ELEMENT DATA
7. A W Mf i l t e r
JUMP #254
Summary: The two filters of each element can be
used to control the tone in various ways.
Procedure:
From: AWM Element job (JUMP #256)
directory
Select: job 07:Filter (JUMP #264)
Specify: the desired filter edit job and press
ENTER
Move the cursor in this area to select a job and
press ENTER to move to the selected job.
01: Cutoff Frequency: Make overall settings for
the filters. (JUMP #265)
02: Cutoff Scaling: Specify how each filter will be
adjusted across the keyboard. (JUMP #266,
#267)
03: Cutoff EG: Specify how each filter will
change over time. (JUMP #268, #269, #270,
#271)
Pressing F1-F3 will select the corresponding job.
Note: Filter settings for an AWM element are
exactly the same as for an AFM element. For
details, refer to AFM element job 8. AFM filter.
146
Summary of Contents for SY-77
