Yamaha Star XVS11ATC Owner'S Manual Download | Manualshive

Page: 78 / 104

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-33

6

8. Place the ignitor unit panel in the

original position and install the
quick fasteners.

NOTE:

To install a quick fastener, push its pin
back so that it will protrude from the fas-
tener head, then insert the fastener and
push the protruding pin in until it is flush
with the fastener head.

9. Install the rider seat.

EAU23792

Replacing the headlight bulb

This model is equipped with a quartz
bulb headlight. If the headlight bulb
burns out, replace it as follows.

1. Remove the headlight unit by re-

moving the screws.

2. Disconnect the headlight coupler,

and then remove the bulb cover.

3. Unhook the headlight bulb holder,

and then remove the defective
bulb.

WARNING

EWA10790

Headlight bulbs get very hot. There-
fore, keep flammable products away
from a lit headlight bulb, and do not
touch the bulb until it has cooled
down.

4. Place a new headlight bulb into po-

sition, and then secure it with the
bulb holder.

CAUTION:

ECA10660

Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the bulb,
and the bulb life will be adversely af-

1. Quick fastener (after removal)

2. Quick fastener (before installation)

1. Screw

1. Headlight bulb holder

U3B812E0.book Page 33 Tuesday, May 15, 2007 2:52 PM

«
...
76
77
78
79
80
...
»

Summary of Contents for Star XVS11ATC









































































































Reviews:

No comments

Related manuals for Star XVS11ATC

Brand: DAELIM Pages: 2

Brand: Parkside Pages: 89

Brand: Parkside Pages: 28

Brand: hepco & becker Pages: 4

Brand: N-Com Pages: 2

HIGHSIDER VICTORY

Brand: Paaschburg & Wunderlich Pages: 5

Brand: Honda Pages: 110

Brand: Triumph Pages: 53

Brand: Toolland Pages: 25

Brand: MW TOOLS Pages: 9

Brand: Barton Pages: 35

Brand: SHERCO Pages: 54

Brand: Engelbert Strauss Pages: 46

Brand: Warn Pages: 8

Brand: Bagster Pages: 2

Brand: RIEJU Pages: 7

Brand: RIEJU Pages: 79

Brand: ZTechnik Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands