Yamaha Star XVS11ATC Owner'S Manual Download | Manualshive

Page: 60 / 104

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-15

6

EAU21382

Checking the throttle cable
free play

The throttle cable free play should mea-
sure 4.0–6.0 mm (0.16–0.24 in) at the
throttle grip. Periodically check the
throttle cable free play and, if neces-
sary, have a Yamaha dealer adjust it.

EAU21401

Valve clearance

The valve clearance changes with use,
resulting in improper air-fuel mixture
and/or engine noise. To prevent this
from occurring, the valve clearance
must be adjusted by a Yamaha dealer
at the intervals specified in the periodic
maintenance and lubrication chart.

EAU32520

Tires (XVS11X)

To maximize the performance, durabil-
ity, and safe operation of your motor-
cycle, note the following points
regarding the specified tires.

Tire air pressure

The tire air pressure should be checked
and, if necessary, adjusted before each
ride.

WARNING

EWA10500

●

The tire air pressure must be
checked and adjusted on cold
tires (i.e., when the temperature
of the tires equals the ambient
temperature).

●

The tire air pressure must be ad-
justed in accordance with the
riding speed and with the total
weight of rider, passenger, car-
go, and accessories approved
for this model.

1. Throttle cable free play

U3B812E0.book Page 15 Tuesday, May 15, 2007 2:52 PM

«
...
58
59
60
61
62
...
»

Summary of Contents for Star XVS11ATC









































































































Reviews:

No comments

Related manuals for Star XVS11ATC

Brand: Caberg Pages: 16

Brand: ACERBIS Pages: 72

Brand: GAS GAS Pages: 72

Brand: N-Com Pages: 2

Brand: Cobra Pages: 38

Brand: VEB Pages: 63

Krauser 630.2516

Brand: hepco & becker Pages: 6

Brand: AC Schnitzer Pages: 44

Brand: ESAB Pages: 4

Brand: hepco & becker Pages: 3

Brand: hepco & becker Pages: 4

Brand: Dynafit Pages: 52

ES350 BURROeSCOOTER

Brand: Burro Max Pages: 32

Brand: Benelli Pages: 32

Brand: Benelli Pages: 77

Brand: Abus Pages: 35

Brand: Honda Pages: 146

2012 250 EXC-F SIX DAYS

Brand: KTM Pages: 120

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands