Yamaha Star XVS11ATC Owner'S Manual Download | Manualshive

Page: 43 / 104

background image

OPERATION AND IMPORTANT RIDING POINTS

5-3

5

EAU16671

Shifting

XVS11X

XVS11AWX/XVS11ATX

Shifting gears lets you control the
amount of engine power available for
starting off, accelerating, climbing hills,
etc.
The gear positions are shown in the il-
lustration.

NOTE:

To shift the transmission into the neu-
tral position, press the shift pedal down
repeatedly until it reaches the end of its
travel, and then slightly raise it.

CAUTION:

ECA10260

●

Even with the transmission in
the neutral position, do not
coast for long periods of time
with the engine off, and do not
tow the motorcycle for long dis-
tances. The transmission is
properly lubricated only when
the engine is running. Inade-
quate lubrication may damage
the transmission.

●

Always use the clutch while
changing gears to avoid damag-
ing the engine, transmission,

and drive train, which are not
designed to withstand the
shock of forced shifting.

EAU16680

To start out and accelerate

1. Pull the clutch lever to disengage

the clutch.

2. Shift the transmission into first

gear. The neutral indicator light
should go out.

3. Open the throttle gradually, and at

the same time, release the clutch
lever slowly.

4. At the recommended shift points

shown in the following table, close
the throttle, and at the same time,
quickly pull the clutch lever in.

5. Shift the transmission into second

gear. (Make sure not to shift the
transmission into the neutral posi-
tion.)

6. Open the throttle part way and

gradually release the clutch lever.

7. Follow the same procedure when

shifting to the next higher gear.

1. Shift pedal

2. Neutral position

1. Shift pedal
2. Neutral position

U3B812E0.book Page 3 Tuesday, May 15, 2007 2:52 PM

«
...
41
42
43
44
45
...
»

Summary of Contents for Star XVS11ATC









































































































Reviews:

No comments

Related manuals for Star XVS11ATC

Brand: Fantic Motor Pages: 130

Brand: Dayi Motor Pages: 15

Brand: Yamaha Pages: 96

Brand: Ohlins Pages: 8

Brand: Avenger Pages: 31

Brand: Jialing Honda Pages: 10

Brand: Wedze Pages: 63

Grizzly Minicross RCX/12 50CC

Brand: Malaguti Pages: 33

Brand: Honda Pages: 556

Brand: hepco & becker Pages: 4

Brand: hepco & becker Pages: 4

Brand: hepco & becker Pages: 4

VIKING 2450 Series

Brand: Lincoln Electric Pages: 48

Brand: Kuberg Pages: 38

Brand: Shark Pages: 16

TERMOSCUD R224X

Brand: tucanourbano Pages: 4

Brand: Yamaha Pages: 66

Brand: Yamaha Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands