Yamaha Star XVS11ATC Owner'S Manual Download Page 29

Page: 29 / 104

INSTRUMENT AND CONTROL FUNCTIONS

3-10

Rider seat

To remove the rider seat

1. Remove the passenger seat.
2. Remove the bolts and passenger

seat holder, and then pull the rider
seat up.

To install the rider seat

1. Insert the projections on the front

of the rider seat into the seat hold-
ers as shown, and then place the
seat in the original position.

2. Install the passenger seat holder

and bolts.

3. Install the passenger seat.

NOTE:

Make sure that the seats are properly
secured before riding.

Tightening torque:

Passenger seat nut:

13 Nm (1.3 m·kgf, 9.4 ft·lbf)

1. Projection

2. Seat holder

1. Bolt
2. Passenger seat holder

1. Projection
2. Seat holder

U3B812E0.book Page 10 Tuesday, May 15, 2007 2:52 PM

Summary of Contents for Star XVS11ATC









































































































Search results

Summary of Contents for Star XVS11ATC

Reviews:

Related manuals for Star XVS11ATC

Brands by name

Popular brands

Yamaha Star XVS11ATC, Owner'S Manual

Search results

Summary of Contents for Star XVS11ATC

Reviews:

Related manuals for Star XVS11ATC

Brands by name

Popular brands