Yamaha Star XVS11ATC Owner'S Manual Download

Page: 45 / 104

OPERATION AND IMPORTANT RIDING POINTS

5-5

CAUTION:

ECA10331

After 1000 km (600 mi) of operation,
the engine oil and final gear oil must
be changed, and the oil filter car-
tridge or element replaced.

1600 km (1000 mi) and beyond

The vehicle can now be operated nor-
mally.

CAUTION:

ECA10270

If any engine trouble should occur
during the engine break-in period,
immediately have a Yamaha dealer
check the vehicle.

EAU17180

Parking

When parking, stop the engine, remove
the key from the main switch, and then
turn the fuel cock lever to “OFF”.

WARNING

EWA10310

●

Since the engine and exhaust
system can become very hot,
park in a place where pedestri-
ans or children are not likely to
touch them.

●

Do not park on a slope or on soft
ground, otherwise the vehicle
may overturn.

CAUTION:

ECA10380

Never park in an area where there
are fire hazards such as grass or
other flammable materials.

U3B812E0.book Page 5 Tuesday, May 15, 2007 2:52 PM

Summary of Contents for Star XVS11ATC









































































































Search results

Summary of Contents for Star XVS11ATC

Reviews:

Related manuals for Star XVS11ATC

Brands by name

Popular brands

Yamaha Star XVS11ATC, Owner'S Manual

Search results

Summary of Contents for Star XVS11ATC

Reviews:

Related manuals for Star XVS11ATC

Brands by name

Popular brands