Yamaha Star XVS11ATC Owner'S Manual Download

Page: 72 / 104

PERIODIC MAINTENANCE AND MINOR REPAIR

6-27

EAU23141

Checking and lubricating the
brake and clutch levers

The operation of the brake and clutch
levers should be checked before each
ride, and the lever pivots should be lu-
bricated if necessary.

EAU23200

Checking and lubricating the
sidestand

The operation of the sidestand should
be checked before each ride, and the
sidestand pivot and metal-to-metal
contact surfaces should be lubricated if
necessary.

WARNING

EWA10730

If the sidestand does not move up
and down smoothly, have a Yamaha
dealer check or repair it.

Recommended lubricants:

Brake pedal:

Silicone grease

Shift pedal:

Lithium-soap-based grease (all-
purpose grease)

Recommended lubricants:

Brake lever:

Silicone grease

Clutch lever:

Lithium-soap-based grease (all-
purpose grease)

Recommended lubricant:

Lithium-soap-based grease (all-pur-
pose grease)

U3B812E0.book Page 27 Tuesday, May 15, 2007 2:52 PM

Summary of Contents for Star XVS11ATC









































































































Search results

Summary of Contents for Star XVS11ATC

Reviews:

Related manuals for Star XVS11ATC

Brands by name

Popular brands

Yamaha Star XVS11ATC, Owner'S Manual

Search results

Summary of Contents for Star XVS11ATC

Reviews:

Related manuals for Star XVS11ATC

Brands by name

Popular brands