Yamaha Star XVS11ATC Owner'S Manual Download Page 66 | Manualshive

Page: 66 / 104

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-21

6

●

After repairing or replacing the rear
tire, tighten the valve stem nut and
locknut to the specified torques.

EAU22011

Accessories and replacement
parts

WARNING

EWA10621

This vehicle is not designed to pull a
trailer or to be attached to a sidecar.
The accessories or replacement
parts you choose for your vehicle
should be designed specifically for
this model, and they must be se-
curely mounted to maintain the in-
herent stability of the original
design. Genuine Yamaha Parts and
Accessories are designed and test-
ed to be compatible with your vehi-
cle. Please consider Genuine
Yamaha Parts and Accessories be-
fore making a purchase. Use of non-
Yamaha-approved accessories or
replacement parts may cause loss of
handling stability and riding safety.
Since Yamaha cannot control the
quality of accessories or parts man-
ufactured by other companies,
Yamaha cannot be held liable for

any consequences caused by the
use of items which have not been
approved by Yamaha.

1. Valve stem nut
2. Valve stem locknut

Tightening torques:

Valve stem nut:

1.5 Nm (0.15 m·kgf, 1.08 ft·lbf)

Valve stem locknut:

3.0 Nm (0.30 m·kgf, 2.17 ft·lbf)

2

1

U3B812E0.book Page 21 Tuesday, May 15, 2007 2:52 PM

«
...
64
65
66
67
68
...
»

Summary of Contents for Star XVS11ATC









































































































Reviews:

No comments

Related manuals for Star XVS11ATC

Brand: N-Com Pages: 2

Brand: N-Com Pages: 64

Brand: CB Sabbiatrici Pages: 43

Brand: Victory Motorcycles Pages: 332

Brand: DUCATI Performance Pages: 9

Brand: Honda Pages: 325

Brand: hepco & becker Pages: 4

Brand: SHERCO Pages: 76

Brand: Bajaj Pages: 319

Dirt rocket XM500

Brand: X-TREME scooter Pages: 14

Brand: hepco & becker Pages: 3

Brand: DYNATEK Pages: 8

Brand: BMW Motorrad Pages: 28

Brand: BMW Motorrad Pages: 170

Brand: Star Motorcycles Pages: 19

Brand: APRILIA Pages: 197

Brand: hepco & becker Pages: 2

Brand: hepco & becker Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands