Yamaha Star XVS11ATC Owner'S Manual Download | Manualshive

Page: 34 / 104

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-15

3

XVS11X

XVS11AWX/XVS11ATX

6. Install the mudguard and ignitor

unit panel by installing the quick
fasteners.

NOTE:

To install a quick fastener, push the pin
back so that it will protrude from the fas-
tener head, and then insert the fastener
and push the protruding pin in until it is
flush with the fastener head.

7. Install the rider seat.

WARNING

EWA10220

This shock absorber contains highly
pressurized nitrogen gas. For prop-
er handling, read and understand
the following information before
handling the shock absorber. The
manufacturer cannot be held re-
sponsible for property damage or
personal injury that may result from
improper handling.

●

Do not tamper with or attempt to
open the gas cylinder.

1. Spring preload adjusting ring

2. Position indicator

3. Special wrench

1. Position indicator
2. Spring preload adjusting ring

3. Special wrench

Spring preload setting:

Minimum (soft):

1

Standard:

XVS11X 3
XVS11AWX 4
XVS11ATX 4

Maximum (hard):

XVS11X 7
XVS11AWX 9
XVS11ATX 9

1. Quick fastener (after removal)
2. Quick fastener (before installation)

U3B812E0.book Page 15 Tuesday, May 15, 2007 2:52 PM

«
...
32
33
34
35
36
...
»

Summary of Contents for Star XVS11ATC









































































































Reviews:

No comments

Related manuals for Star XVS11ATC

Brand: ZERO GRAVITY Pages: 6

Brand: Baotian Pages: 30

Brand: Can-Am Pages: 16

Brand: Can-Am Pages: 254

HIGHSIDER VICTORY

Brand: Paaschburg & Wunderlich Pages: 5

Brand: R&G Pages: 9

Brand: DYNATEK Pages: 8

Brand: Yamaha Pages: 80

Brand: Yamaha Pages: 63

Brand: Yamaha Pages: 78

Brand: Yamaha Pages: 94

Star XV1900AE 2013

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 84

Brand: Yamaha Pages: 94

Brand: Yamaha Pages: 86

Brand: Yamaha Pages: 99

Brand: Yamaha Pages: 96

Brand: Yamaha Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands