Yamaha Star XVS11ATC Owner'S Manual Download | Manualshive

Page: 71 / 104

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-26

6

EAU23091

Checking and lubricating the
cables

The operation of all control cables and
the condition of the cables should be
checked before each ride, and the ca-
bles and cable ends should be lubricat-
ed if necessary. If a cable is damaged
or does not move smoothly, have a
Yamaha dealer check or replace it.

WARNING

EWA10710

Damage to the outer housing of ca-
bles may result in internal rusting
and cause interference with cable
movement. Replace damaged ca-
bles as soon as possible to prevent
unsafe conditions.

EAU23111

Checking and lubricating the
throttle grip and cable

The operation of the throttle grip should
be checked before each ride. In addi-
tion, the cable should be lubricated at
the intervals specified in the periodic
maintenance chart.

EAU23132

Checking and lubricating the
brake and shift pedals

The operation of the brake and shift
pedals should be checked before each
ride, and the pedal pivots should be lu-
bricated if necessary.

Recommended lubricant:

Yamaha Chain and Cable Lube or
engine oil SAE 10W-30

U3B812E0.book Page 26 Tuesday, May 15, 2007 2:52 PM

«
...
69
70
71
72
73
...
»

Summary of Contents for Star XVS11ATC









































































































Reviews:

No comments

Related manuals for Star XVS11ATC

Brand: oset Pages: 20

Brand: Bajaj Pages: 55

Brand: B-PWR Pages: 13

Brand: Ohlins Pages: 8

Brand: GYS Pages: 36

Brand: Crivit Pages: 50

Brand: Honda Pages: 98

Virago XV1100K(C)

Brand: Yamaha Pages: 111

Brand: Yamaha Pages: 101

Brand: PMI Pages: 2

Brand: Honda Pages: 123

Brand: hepco & becker Pages: 3

Brand: R&G Pages: 9

Brand: R&G Pages: 11

Brand: Fuelpak Pages: 2

Brand: SPmoto Pages: 92

Brand: Honda Pages: 117

CRF250L/LA Rally 2020

Brand: Honda Pages: 139

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands