Yamaha Star XVS11ATC Owner'S Manual Download | Manualshive

Page: 44 / 104

background image

OPERATION AND IMPORTANT RIDING POINTS

5-4

5

NOTE:

Always shift gears at the recommended
shift points.

EAU16700

To decelerate

1. Apply both the front and the rear

brakes to slow the motorcycle.

2. Shift the transmission into first

gear when the motorcycle reaches
25 km/h (15.5 mi/h). If the engine is
about to stall or runs very roughly,
pull the clutch lever in and use the
brakes to stop the motorcycle.

3. Shift the transmission into the neu-

tral position when the motorcycle
is almost completely stopped. The
neutral indicator light should come
on.

EAU16720

Recommended shift points

The recommended shift points during
acceleration and deceleration are
shown in the table below.

EAU16841

Engine break-in

There is never a more important period
in the life of your engine than the period
between 0 and 1600 km (1000 mi). For
this reason, you should read the follow-
ing material carefully.
Since the engine is brand new, do not
put an excessive load on it for the first
1600 km (1000 mi). The various parts in
the engine wear and polish themselves
to the correct operating clearances.
During this period, prolonged full-throt-
tle operation or any condition that might
result in engine overheating must be
avoided.

EAU17041

0–1000 km (0–600 mi)

Avoid prolonged operation above 1/3
throttle.

1000–1600 km (600–1000 mi)

Avoid prolonged operation above 1/2
throttle.

Shift up points:

1st

→

2nd: 20 km/h (12.4 mi/h)

2nd

→

3rd: 30 km/h (18.6 mi/h)

3rd

→

4th: 40 km/h (24.9 mi/h)

4th

→

5th: 50 km/h (31.1 mi/h)

Shift down points:

5th

→

4th: 25 km/h (15.5 mi/h)

4th

→

3rd: 25 km/h (15.5 mi/h)

3rd

→

2nd: 25 km/h (15.5 mi/h)

2nd

→

1st: 25 km/h (15.5 mi/h)

U3B812E0.book Page 4 Tuesday, May 15, 2007 2:52 PM

«
...
42
43
44
45
46
...
»

Summary of Contents for Star XVS11ATC









































































































Reviews:

No comments

Related manuals for Star XVS11ATC

Brand: KAYO MOTOR Pages: 84

Apache RTR 160 HYPER EDGE 2015

Brand: TVS Pages: 60

Brand: hepco & becker Pages: 4

TXT ROOKIE - 2006

Brand: GAS GAS Pages: 32

Brand: Big Bike Parts Pages: 3

Brand: GAS GAS Pages: 26

Brand: DYNATEK Pages: 3

Brand: DYNATEK Pages: 8

Brand: Faller Pages: 8

Brand: IBEX Pages: 3

gtrack 7855 MyBASIC

Brand: Gemini Pages: 20

F12R AIR 50 cc. - Euro 2

Brand: Malaguti Pages: 46

Brand: APRILIA Pages: 80

Brand: R&G Pages: 19

Brand: Artago Pages: 4

Brand: Oxford Pages: 2

Brand: Beta Pages: 93

2009 Evo 2T 125

Brand: Beta Pages: 192

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands