Yamaha FL200C Page 96 Owner'S Manual Download

Page: 96 / 100

INDEX

meters ................................................ 35

6Y8 Multifunction meters...................... 30
6Y8 Multifunction speed & fuel

meters ................................................ 33

6Y8 Multifunction speedometers.......... 34
6Y8 Multifunction tachometers ............ 30

Alcohol and drugs................................... 2
Alert system .......................................... 36
Anode(s), inspecting and replacing ...... 78
Anti-fouling paint .................................. 13
Avoid collisions....................................... 3

Battery .................................................. 45
Battery, checking (electric start

models)............................................... 79

Battery, connecting .............................. 79
Battery, disconnecting.......................... 81
Battery requirements ............................ 11
Boat horsepower rating ........................ 10
Boating safety......................................... 2
Boating safety publications .................... 3
Breaking in engine ................................ 40

conditions........................................... 56

Digital speedometer.............................. 25
Digital tachometer ................................ 24
Draining the gasoline from the vapor

separator ............................................ 59

EC Declaration of Conformity (DoC) ....... 4
Electric shock ......................................... 1
Emergency equipment.......................... 14
Emergency, running single engine in

an........................................................ 85

Emergency, temporary action in........... 85
Engine, checking .................................. 42
Engine oil .............................................. 42
Engine oil, changing ............................. 68
Engine oil, filling .................................... 40
Engine oil requirements ........................ 12
Engine shut-off cord (lanyard) .......... 1, 42
Engine shut-off cord (lanyard) and

clip ...................................................... 18

Engine trouble alert............................... 32

Filling fuel.............................................. 45
First-time operation .............................. 40
Flushing device............................... 22, 42
Flushing power unit .............................. 59
Flushing with a flushing attachment

(F200C, FL200C, F225B, FL225B) ..... 58

U6P27AE0.book Page 90 Friday, December 6, 2013 6:17 PM

Summary of Contents for FL200C





































































































Search results

Summary of Contents for FL200C

Reviews:

Related manuals for FL200C

Brands by name

Popular brands

Yamaha FL200C, Owner'S Manual

Search results

Summary of Contents for FL200C

Reviews:

Related manuals for FL200C

Brands by name

Popular brands