Yamaha FL200C Page 49 Owner'S Manual Download

Page: 49 / 100

Operation

garden hose connector is not properly
connected, cooling water can leak out and
the engine can overheat during operation.

[ECM01802]

EMU36942

Install cowling

Be sure that all cowling lock levers are
released.

Be sure that the rubber seal is seated all
the way around the engine.

Place the cowling on top of the seal.

Check to be sure it fits properly in the
rubber seal.

Move the levers to lock the cowling as
shown.

NOTICE:

If the top cowling is

not installed correctly, water spray
under the top cowling can damage the
engine, or the top cowling can blow
off at high speeds.

[ECM01992]

After installing, check the fitting of the top
cowling by pushing it with both hands. If the
top cowling is loose, have it repaired by your
Yamaha dealer.

1. Fitting
2. Flushing device

ZMU06164

ZMU06131

ZMU06133

U6P27AE0.book Page 43 Friday, December 6, 2013 6:17 PM

Summary of Contents for FL200C





































































































Search results

Summary of Contents for FL200C

Reviews:

Related manuals for FL200C

Brands by name

Popular brands

Yamaha FL200C, Owner'S Manual

Search results

Summary of Contents for FL200C

Reviews:

Related manuals for FL200C

Brands by name

Popular brands