Yamaha FL200C Page 19 Owner'S Manual Download | Manualshive

Page: 19 / 100

background image

Specifications and requirements

13

Recommended engine oil grade 2

EMU36361

Fuel requirements

EMU40202

Gasoline

Use a good quality gasoline that meets the
minimum octane rating. If knocking or ping-
ing occurs, use a different brand of gasoline
or premium unleaded fuel.

NOTICE

ECM01982



Do not use leaded gasoline. Leaded
gasoline can seriously damage the en-
gine.



Avoid getting water and contaminants in
the fuel tank. Contaminated fuel can
cause poor performance or engine dam-
age. Use only fresh gasoline that has
been stored in clean containers.

Gasohol

There are two types of gasohol: gasohol con-
taining ethanol (E10) and that containing
methanol. Ethanol can be used if the ethanol
content does not exceed 10% and the fuel
meets the minimum octane ratings. E85 is a
fuel containing 85% ethanol and must not be
used in your outboard motor. All ethanol
blends containing more than 10% ethanol
can cause fuel system damage or cause en-
gine starting and running problems. Yamaha
does not recommend gasohol containing
methanol because it can cause fuel system
damage or engine performance problems.
It is recommended that you install a water-
separating marine fuel filter assembly (10 mi-
cron minimum) between your boat’s fuel tank
and outboard motor when using ethanol. Eth-
anol is known to allow moisture to be ab-
sorbed into boat fuel tanks and systems.
Moisture in the fuel can cause corrosion of
metallic fuel system components, starting
and running complaints and require addition-
al fuel system maintenance.

EMU36331

Anti-fouling paint

A clean hull improves boat performance. The
boat bottom should be kept as clean of ma-
rine growth as possible. If necessary, the
boat bottom can be coated with an anti-foul-
ing paint approved for your area to inhibit ma-
rine growth.
Do not use anti-fouling paint which includes
copper or graphite. These paints can cause
more rapid engine corrosion.

Recommended fuel:

F200CET Regular unleaded gasoline
F225BET Regular unleaded gasoline
F225CET Premium unleaded gasoline
FL200CET Regular unleaded gasoline
FL225BET Regular unleaded gasoline

Min. research octane number (RON):

F200CET 90
F225BET 90
F225CET 94
FL200CET 90
FL225BET 90

ZMU06855

122˚F

50˚C

104

40

86

30

68

SAE

API

SH

SJ
SL

20

50

10

32

0

14

-10

-4

-20

15W–40

20W–40

20W–50

U6P27AE0.book Page 13 Friday, December 6, 2013 6:17 PM

«
...
17
18
19
20
21
...
»

Summary of Contents for FL200C





































































































Reviews:

No comments

Related manuals for FL200C

Brand: AKM Pages: 34

Brand: ASROCK Pages: 2

Brand: QDI Pages: 20

Fatal1ty Z87 Killer Series

Brand: ASROCK Pages: 102

Brand: Texas Instruments Pages: 18

Tiger MPX S2466

Brand: TYAN Pages: 1

Avnet Ultra96-PYNQ

Brand: Xilinx Pages: 19

MBD-X11SDV-4C-TP8F-B

Brand: Supermicro Pages: 123

NVIDIA MS-7504PV

Brand: MSI Pages: 50

Brand: Advantech Pages: 5

Brand: AZZA Pages: 43

Brand: Texas Instruments Pages: 19

Brand: Panasonic Pages: 5

Brand: Panasonic Pages: 11

PGA26E07BA-SWEVB006

Brand: Panasonic Pages: 17

Brand: Panasonic Pages: 15

Brand: Panasonic Pages: 15

EvalBoard PAN4555

Brand: Panasonic Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands