background image

Operation

41

NOTICE

ECM00121

Do not start the engine out of water. Over-
heating and serious engine damage can
occur.

EMU36422

Fuel level

Be sure you have plenty of fuel for your trip. A
good rule is to use 1/3 of your fuel to get to
the destination, 1/3 to return, and to keep 1/3
as an emergency reserve. With the boat level
on a trailer or in the water, turn the key to “

(on) and check the fuel level. For fuel filling in-
structions, see page 45.

EMU36433

Remove cowling

For the following checks, remove the top
cowling from the engine. To remove the en-
gine cowling, release all the lock levers and
lift off the cowling.

EMU36443

Fuel system

WARNING

EWM00061

Gasoline and its vapors are highly flamma-
ble and explosive. Keep away from sparks,
cigarettes, flames, or other sources of ig-
nition.

WARNING

EWM00911

Leaking fuel can result in fire or explosion.

Check for fuel leakage regularly.

If any fuel leakage is found, the fuel sys-
tem must be repaired by a qualified me-
chanic. Improper repairs can make the
outboard unsafe to operate.

EMU36452

Check for fuel leaks

Check for fuel leaks or gasoline fumes in
the boat.

Check for fuel leakage from the fuel sys-
tem.

Check the fuel tank and fuel lines for
cracks, swellings, or other damages.

EMU37323

Checking the fuel filter

Check that the fuel filter is clean and free of
water. If any water is found in the fuel, or if a
significant amount of debris is found, the fuel
tank should be checked and cleaned by a
Yamaha dealer.

ZMU06106

ZMU06108

ZMU07545

U6P27AE0.book  Page 41  Friday, December 6, 2013  6:17 PM

Summary of Contents for FL200C





































































































Reviews: