manualshive.com logo in svg

Yamaha FL200C, Owner'S Manual, Page: 51 / 100

Share
Download
Yamaha FL200C Owner'S Manual Download Page 51

Operation

45

6.

Activate the tilt-down switch until the
trim rods have retracted completely into
the cylinders.

F200C, FL200C, F225B, FL225B

F225C

7.

Activate the trim-up switch until the tilt
rod is fully extended. Unlock the tilt sup-
port lever.

F200C, FL200C, F225B, FL225B

F225C

8.

Tilt the outboard motor down. Check
that the tilt rod and trim rods operate
smoothly.

EMU36583

Battery

Check that the battery is in good condition,
and fully charged. Check that the battery
connections are clean, secure and covered
by insulating covers. The electrical contacts
of the battery and cables must be clean and
properly connected or the battery will not
start the engine.
Refer to the battery manufacturer’s instruc-
tions for checks for your particular battery.

EMU30027

Filling fuel 

WARNING

EWM01831

Gasoline and its vapors are highly flam-
mable and explosive. Always refuel ac-
cording to this procedure to reduce the
risk of fire and explosion.

Gasoline is poisonous and can cause in-
jury or death. Handle gasoline with care.
Never siphon gasoline by mouth. If you
should swallow some gasoline or inhale
a lot of gasoline vapor, or get some gas-
oline in your eyes, see your doctor im-
mediately. If gasoline spills on your skin,

ZMU03452

ZMU01885

ZMU02635

U6P27AE0.book  Page 45  Friday, December 6, 2013  6:17 PM

Summary of Contents for FL200C





































































































Reviews:

No comments