manualshive.com logo in svg

Yamaha FL200C, Owner'S Manual, Page: 59 / 100

Share
Download
Yamaha FL200C Owner'S Manual Download Page 59

Operation

53

To prevent the cooling water passages
from becoming frozen when the ambi-
ent temperature is 5°C (41°F) or below,
tilt the outboard motor up after it has
been stopped 30 seconds or more.

EMU42683

Procedure for tilting up

1.

Place the remote control lever in neutral.

2.

Press the power trim and tilt switch “

”

(up) until the outboard motor has tilted
up completely.

3.

Pull the tilt support lever toward you to
support the engine. 

WARNING! After

tilting the outboard motor, be sure to
support it with the tilt support knob or
tilt support lever. Otherwise the out-
board motor could fall back down
suddenly if oil in the power trim and tilt
unit or in the power tilt unit loses pres-
sure.

 [EWM00263]

 

NOTICE:

 Do not use the

tilt support lever or knob when traile-
ring the boat. The outboard motor
could shake loose from the tilt support
and fall. If the motor cannot be
trailered in the normal running posi-
tion, use an additional support device
to secure it in the tilt position. For
more detailed information, see page
57.

 [ECM01642]

N

ZMU07396

UP

ZMU04194

ZMU07398

UP

U6P27AE0.book  Page 53  Friday, December 6, 2013  6:17 PM

Summary of Contents for FL200C





































































































Reviews:

No comments