Yamaha FL200C Page 81 Owner'S Manual Download

Page: 81 / 100

Maintenance

F200C, FL200C, F225B, FL225B

F225C

TIP:

Make sure to align the protrusions on the
spacer with the cutout areas of the propeller.
4.

Align the propeller nut slot with the pro-
peller shaft hole. Insert a new cotter pin
in the hole and bend the cotter pin ends.

NOTICE:

Do not reuse the cotter pin.

Otherwise, the propeller can come off
during operation.

[ECM01892]

TIP:

If the propeller nut slot does not align with the
propeller shaft hole after tightening the pro-
peller nut to the specified torque, tighten the
nut further to align the slot with the hole.

EMU42573

Changing gear oil

F200C, FL200C, F225B, FL225B

WARNING

EWM00801



Be sure the outboard motor is securely
fastened to the transom or a stable
stand. You could be severely injured if
the outboard motor falls on you.

1. Cotter pin
2. Propeller nut
3. Washer
4. Spacer
5. Propeller
6. Thrust washer

1. Cotter pin
2. Propeller nut
3. Washer
4. Spacer
5. Propeller
6. Spacer

ZMU07549

4 3

ZMU07548

4 3

7. Thrust washer

Propeller nut tightening torque:

54 Nm (5.51 kgf-m, 39.8 ft-lb)

1. Cotter pin

ZMU06956

U6P27AE0.book Page 75 Friday, December 6, 2013 6:17 PM

Summary of Contents for FL200C





































































































Search results

Summary of Contents for FL200C

Reviews:

Related manuals for FL200C

Brands by name

Popular brands

Yamaha FL200C, Owner'S Manual

Search results

Summary of Contents for FL200C

Reviews:

Related manuals for FL200C

Brands by name

Popular brands