manualshive.com logo in svg

Yamaha FL200C, Owner'S Manual, Page: 31 / 100

Share
Download
Yamaha FL200C Owner'S Manual Download Page 31

Instruments and indicators

25

EMU26525

Low oil pressure-alert indicator

If oil pressure drops too low, the alert indica-
tor will start to blink. For further information,
see page 36.

NOTICE

ECM00023

Do not continue to run the engine if the
low oil pressure-alert indicator is on and
the engine oil level is lower. Serious en-
gine damage will occur.

The low oil pressure-alert indicator does
not indicate the engine oil level. Use the
oil dipstick to check the remaining oil
quantity. For further information, see
page 42.

EMU26584

Overheat-alert indicator

If the engine temperature rises too high, the
alert indicator will start to blink. For further in-
formation on reading the indicator, see page
36.

NOTICE

ECM00053

Do not continue to run the engine if the
overheat-alert indicator is on. Serious en-
gine damage will occur.

EMU26603

Digital speedometer

This gauge shows the boat speed and other
information.

All segments of the display will light momen-
tarily after the main switch is turned on and
will return to normal thereafter.

EMU36062

Speedometer

The speedometer displays km/h, mph, or
knots, according to operator preference. Se-
lect the desired units of measurement by set-
ting the selector switch on the back of the
gauge. See the illustration for settings.

1. Low oil pressure-alert indicator

ZMU01736

1

1. Overheat-alert indicator

1. Speedometer
2. Fuel gauge
3. Trip meter/clock/voltmeter
4. Alert indicator(s)

ZMU01737

1

U6P27AE0.book  Page 25  Friday, December 6, 2013  6:17 PM

Summary of Contents for FL200C





































































































Reviews:

No comments