Yamaha FL200C Owner'S Manual Download

Page: 92 / 100

Trouble Recovery

NOTICE

ECM00371

If the boat is operated with one engine in
the water but not running, water may run
into the exhaust pipe due to wave action,
causing engine trouble.

TIP:

When you are maneuvering at low speed,
such as near a dock, it is recommended that
both engines be running with one in neutral
gear if possible.

EMU29475

Replacing fuse

If a fuse has blown, remove the electrical cov-
er, open the fuse holder and remove the fuse
with a fuse puller (if equipped). Replace it with
a spare one of the proper amperage.

WARNING

EWM00632

Substituting an incorrect fuse or a piece of
wire could allow excessive current flow.
This could cause electric system damage
and a fire hazard.

Consult your Yamaha dealer if the new fuse
immediately blows again.

1. Electrical cover
2. Fuse puller
3. Spare fuse (10 A, 15 A, 20 A, 30 A, 60 A)

1. Electric throttle valve / ECM (Electronic con-

trol module) fuse (10 A)

2. Ignition coil / Fuel injector / Variable cam-

shaft timing / ECM (Electronic Control Mod-
ule) fuse (30 A)

3. Main switch / PTT switch fuse (20 A)
4. Starter relay fuse (30 A)
5. Fuel feed pump fuse (10 A)
6. Fuel pump fuse (15 A)

U6P27AE0.book Page 86 Friday, December 6, 2013 6:17 PM

Summary of Contents for FL200C





































































































Search results

Summary of Contents for FL200C

Reviews:

Related manuals for FL200C

Brands by name

Popular brands

Yamaha FL200C, Owner'S Manual

Search results

Summary of Contents for FL200C

Reviews:

Related manuals for FL200C

Brands by name

Popular brands