Yamaha FL200C Owner'S Manual Download Page 18 | Manualshive

Page: 18 / 100

background image

Specifications and requirements

12

Yamaha recommends to use a propeller suit-
able for the “Shift Dampener System (SDS)”.
For further information, consult your Yamaha
dealer.
To check the propeller, see page 73.

EMU36312

Counter rotation models

Standard outboard motors rotate clockwise.
Counter rotation models rotate counterclock-
wise and are typically used in multiple motor
setups.
On counter rotation models, be sure to use a
propeller intended for counterclockwise rota-
tion. These propellers are identified with the
letter “L” after the size indication on the pro-
peller.

WARNING! Never use a standard

propeller with a counter rotation motor, or
a counter rotation propeller with a stan-
dard motor. Otherwise the boat could go
in the direction opposite of that expected
(for example, reverse instead of forward),
which could lead to an accident.

[EWM01811]

For instructions on propeller removal and in-
stallation, see page 73 and 74.

EMU25771

Start-in-gear protection

Yamaha outboard motors or Yamaha-ap-
proved remote control units are equipped
with start-in-gear protection device(s). This

feature permits the engine to be started only
when it is in neutral. Always select neutral be-
fore starting the engine.

EMU41953

Engine oil requirements

Select an oil grade according to the average
temperatures in the area where the outboard
motor will be used.

If oil grades listed under Recommended en-
gine oil grade 1 are not available, select an al-
ternative oil grade listed under
Recommended engine oil grade 2.

Recommended engine oil grade 1

1. Propeller diameter in inches
2. Propeller pitch in inches
3. Type of propeller (propeller mark)

ZMU07044

3

1

2

Recommended engine oil:

YAMALUBE 4 or 4-stroke outboard
motor oil

Recommended engine oil grade 1:

SAE 10W-30/10W-40/5W-30
API SE/SF/SG/SH/SJ/SL

Recommended engine oil grade 2:

SAE 15W-40/20W-40/20W-50
API SH/SJ/SL
Engine oil quantity (without oil filter
replacement):

4.5 L (4.76 US qt, 3.96 Imp.qt)

Engine oil quantity (with oil filter re-
placement):

4.7 L (4.97 US qt, 4.14 Imp.qt)

ZMU06854

122˚F

50˚C

104

40

86

30

68

SAE

API

SE
SF

SG
SH

SJ
SL

20

50

10

32

0

14

-10

-4

-20

10W–30

10W–40

5W–30

U6P27AE0.book Page 12 Friday, December 6, 2013 6:17 PM

«
...
16
17
18
19
20
...
»

Summary of Contents for FL200C





































































































Reviews:

No comments

Related manuals for FL200C

Brand: Atmel Pages: 22

Brand: CompuLab Pages: 31

Brand: Beagleboard.org Pages: 2

Brand: Texas Instruments Pages: 24

microComponents mp6-XEVA

Brand: Bartels Mikrotechnik Pages: 9

Brand: ASROCK Pages: 154

Z690M DS3H DDR4

Brand: Gigabyte Pages: 36

Brand: Xilinx Pages: 88

Brand: Microchip Technology Pages: 44

Brand: WynMax Pages: 68

Brand: ASROCK Pages: 26

Brand: IBASE Technology Pages: 62

Brand: Supero Pages: 92

Brand: Texas Instruments Pages: 27

X58 Classified3

Brand: EVGA Pages: 2

Brand: Benezan Electronics Pages: 18

Brand: Gigabyte Pages: 19

Brand: Aeroflex Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands