Yamaha 2005 YZF-R1T Owner'S Manual Download Page 87

Page: 87 / 106

PERIODIC MAINTENANCE AND MINOR REPAIR

6-38

EAU24360

Front wheel

EAU33921

To remove the front wheel

WARNING

EWA10820

●

It is advisable to have a Yamaha
dealer service the wheel.

●

Securely support the motor-
cycle so that there is no danger
of it falling over.

1. Loosen the wheel axle pinch bolts,

the axle bolt, and then the brake
caliper bolts.

2. Lift the front wheel off the ground

according to the procedure on
page 6-37.

3. Remove the brake hose holder on

each side by removing the bolt and
nut.

4. Remove the brake caliper on each

side by removing the bolts.

5. Remove the axle bolt, push the

wheel axle out from the left side,
and then remove the wheel.

CAUTION:

ECA11050

Do not apply the brake after the
brake calipers have been removed,
otherwise the brake pads will be
forced shut.

EAU33931

To install the front wheel

1. Lift the wheel up between the fork

legs.

2. Insert the wheel axle.
3. Lower the front wheel so that it is

on the ground.

4. Install the brake calipers by install-

ing the bolts, and then tightening
them to the specified torque.

1. Front wheel axle pinch bolt

1. Brake hose holder
2. Bolt and nut

3. Brake caliper bolt

4. Brake caliper
5. Axle bolt

1. Wheel axle

U5VY21E0.book Page 38 Friday, September 10, 2004 9:21 AM

Summary of Contents for 2005 YZF-R1T











































































































Search results

Summary of Contents for 2005 YZF-R1T

Reviews:

Related manuals for 2005 YZF-R1T

Brands by name

Popular brands

Yamaha 2005 YZF-R1T, Owner'S Manual

Search results

Summary of Contents for 2005 YZF-R1T

Reviews:

Related manuals for 2005 YZF-R1T

Brands by name

Popular brands