Yamaha 2005 YZF-R1T Owner'S Manual Download Page 41

Page: 41 / 106

INSTRUMENT AND CONTROL FUNCTIONS

3-25

below and have a Yamaha dealer re-
pair it if it does not function proper-
ly.

EAU15311

Ignition circuit cut-off system

The ignition circuit cut-off system (com-
prising the sidestand switch, clutch
switch and neutral switch) has the fol-
lowing functions.

●

It prevents starting when the trans-
mission is in gear and the side-
stand is up, but the clutch lever is
not pulled.

●

It prevents starting when the trans-
mission is in gear and the clutch le-
ver is pulled, but the sidestand is
still down.

●

It cuts the running engine when the
transmission is in gear and the sid-
estand is moved down.

Periodically check the operation of the
ignition circuit cut-off system according
to the following procedure.

WARNING

EWA10250

If a malfunction is noted, have a
Yamaha dealer check the system be-
fore riding.

U5VY21E0.book Page 25 Friday, September 10, 2004 9:21 AM

Summary of Contents for 2005 YZF-R1T











































































































Search results

Summary of Contents for 2005 YZF-R1T

Reviews:

Related manuals for 2005 YZF-R1T

Brands by name

Popular brands

Yamaha 2005 YZF-R1T, Owner'S Manual

Search results

Summary of Contents for 2005 YZF-R1T

Reviews:

Related manuals for 2005 YZF-R1T

Brands by name

Popular brands