Yamaha 2005 YZF-R1T Owner'S Manual Download Page 79

Page: 79 / 106

PERIODIC MAINTENANCE AND MINOR REPAIR

6-30

EAU34052

Replacing the fuses

The main fuse and the electronic fuel
injection fuse are located under the rid-
er seat. (See page 3-18.)

The fuse box, which contains the fuses
for the individual circuits, is located be-
hind the cowling shown.

If a fuse is blown, replace it as follows.

NOTE:

Include steps 2–4 and 8–9 only for the
fuses in the fuse box.

1. Turn the key to “OFF” and turn off

the electrical circuit in question.

2. Remove the quick fasteners by

pushing the center in with a screw-
driver, then pulling the fastener
out.

3. Loosen and remove the quick fas-

tener screws, and then slide the
areas of the cowling shown for-
ward.

4. Pull the cowling away from the

motorcycle as shown.

1. Main fuse

2. Electronic fuel injection spare fuse

3. Electronic fuel injection fuse

1. Cowling

1. Quick fastener

1. Quick fastener screw

2. Cowling

U5VY21E0.book Page 30 Friday, September 10, 2004 9:21 AM

Summary of Contents for 2005 YZF-R1T











































































































Search results

Summary of Contents for 2005 YZF-R1T

Reviews:

Related manuals for 2005 YZF-R1T

Brands by name

Popular brands

Yamaha 2005 YZF-R1T, Owner'S Manual

Search results

Summary of Contents for 2005 YZF-R1T

Reviews:

Related manuals for 2005 YZF-R1T

Brands by name

Popular brands