Yamaha 2005 YZF-R1T Owner'S Manual Download Page 81

Page: 81 / 106

PERIODIC MAINTENANCE AND MINOR REPAIR

6-32

8. Place the cowling in its original po-

sition, and then install and tighten
the quick fastener screws.

NOTE:

Make sure that the projections are in-
serted into the slots.

9. Install the quick fasteners.

NOTE:

To install a quick fastener, push its pin
back so that it protrudes from the fas-
tener head, then insert the fastener and
push the protruding pin in until it is flush
with the fastener head.

EAU33900

Replacing a headlight bulb

This model is equipped with quartz bulb
headlights. If a headlight bulb burns
out, replace it as follows.

To replace a high beam headlight
bulb

1. Disconnect the headlight coupler,

and then remove the bulb cover.

2. Unhook the headlight bulb holder,

and then remove the defective
bulb.

1. Slot
2. Projection

1. High beam headlight bulb

2. Low beam headlight bulb

1. Headlight bulb cover
2. Headlight coupler

1. Headlight bulb holder

U5VY21E0.book Page 32 Friday, September 10, 2004 9:21 AM

Summary of Contents for 2005 YZF-R1T











































































































Search results

Summary of Contents for 2005 YZF-R1T

Reviews:

Related manuals for 2005 YZF-R1T

Brands by name

Popular brands

Yamaha 2005 YZF-R1T, Owner'S Manual

Search results

Summary of Contents for 2005 YZF-R1T

Reviews:

Related manuals for 2005 YZF-R1T

Brands by name

Popular brands