Yamaha 2005 YZF-R1T Owner'S Manual Download Page 75

Page: 75 / 106

PERIODIC MAINTENANCE AND MINOR REPAIR

6-26

EAU23200

Checking and lubricating the
sidestand

The operation of the sidestand should
be checked before each ride, and the
sidestand pivot and metal-to-metal
contact surfaces should be lubricated if
necessary.

WARNING

EWA10730

If the sidestand does not move up
and down smoothly, have a Yamaha
dealer check or repair it.

EAUM1650

Lubricating the swingarm
pivots

The swingarm pivots must be lubricat-
ed at the intervals specified in the peri-
odic maintenance and lubrication chart.

Recommended lubricant:

Lithium-soap-based grease (all-pur-
pose grease)

Recommended lubricant:

Lithium-soap-based grease (all-pur-
pose grease)

Recommended lubricant:

Lithium-soap-based grease

U5VY21E0.book Page 26 Friday, September 10, 2004 9:21 AM

Summary of Contents for 2005 YZF-R1T











































































































Search results

Summary of Contents for 2005 YZF-R1T

Reviews:

Related manuals for 2005 YZF-R1T

Brands by name

Popular brands

Yamaha 2005 YZF-R1T, Owner'S Manual

Search results

Summary of Contents for 2005 YZF-R1T

Reviews:

Related manuals for 2005 YZF-R1T

Brands by name

Popular brands